Solid Hardwood Flooring Installation in Spring, TX
Spring Hardwood Flooring installs solid hardwood flooring in Spring, TX, from new ¾-inch oak in a whole house to a few rows that tie a remodeled room into the original floor. Solid wood is milled from one piece of timber, so it can be sanded and refinished again and again over its life.
- ¾-inch solid boards, nailed down over wood subfloors
- 3–5 days of acclimation before the first board goes down
- Most solid installs in Spring land between $5 and $16 a square foot
It's our pick for homes with wood subfloors, and for anyone who wants the floor to outlast the next three paint colors. We nail it down, acclimate it properly and give you a written quote first. Homes in surrounding cities such as Tomball, Klein and Cypress are in our range for solid hardwood too.
Solid Hardwood Flooring Services
Solid hardwood rewards good installation and punishes shortcuts. Here's what we install most often in Spring, and where it makes the most sense. Think of solid hardwood like a cast-iron pan: heavy, a little fussy, and good for generations if it's treated right.
¾-Inch Oak Strip and Plank
Red and white oak are the backbone of solid flooring around here. Narrow 2¼-inch strip gives a classic look, and wider planks up to about 5 inches feel more current.
Oak takes stain evenly, so it's the easiest species to change color later. If you're unsure, a natural or light brown oak is the safest long-term choice.
Matching and Extending Original Floors
Took out a wall, or turned a carpeted den into part of the living room? We extend the old floor by threading new boards into the old courses, matched in species and width.
Then we sand and finish old and new together, so there's no seam where one ends. Done right, guests can't point to where the old room stopped.
Hickory and Maple Solid Hardwood
Hickory ranks near the top of American species for hardness, with dramatic color swings, so it suits homes with big dogs and lots of kids. Maple is hard, smooth and pale.
Walnut and cherry are softer and richer looking, and they work best in quieter rooms like a study or formal dining room. Brazilian cherry and other exotics are available too.
Unfinished, Site-Finished Solid Floors
Raw boards are installed, then sanded flat and finished in your home. Seams come out flush, with no micro-bevels, and the stain can be any color you like.
It takes longer and makes more mess than prefinished, but the surface is truly custom. It's also the way to go when matching an older site-finished floor.
Solid Hardwood Installation Steps
Step 1 · Check the Subfloor
We test moisture in the subfloor, look for loose panels and re-secure them so squeaks don't start on day one.
Step 2 · Acclimate the Wood
The bundles sit in the rooms they're going into for 3–5 days, until their moisture content is close to the subfloor's.
Step 3 · Nail It Down
Boards are blind-nailed through the tongue into the subfloor, with end joints spread out and breathing room at the walls so the wood can move with the seasons.
Step 4 · Sand, Finish, Walk Through
Transitions, stair noses and baseboard go back on. Together we check every room, sort out anything that bugs you, and leave care instructions and a humidity target.
Why Spring Homeowners Choose Us for Solid Hardwood
Solid Hardwood Installation FAQs
It can be glued down where the slab allows, but on most Spring slabs we'd steer you to engineered. Solid shines over a plywood or wood subfloor, where it can be nailed down the traditional way.
Many. A ¾-inch board has a lot of wood above the tongue, which is why floors from the '70s are still being refinished today. Each sanding takes off only a thin layer.
Usually. Most older Spring floors are 2¼-inch red oak strip, which is still widely made. We match width and species, then finish old and new together.
Prefinished goes in faster with less dust. Unfinished, finished on site, gives flush seams and fully custom color. Both last; it comes down to your priorities and schedule.
Hardwood installs in Spring usually run $5–$16 per square foot. Oak and hickory are the most budget-friendly. Exotics and wide planks cost more. Subfloor repairs are priced on their own line.
Aim for 35–55% humidity inside, winter and summer. Small gaps in a dry winter are normal and usually close up when the humidity comes back. Gaps that stay open all year point to a moisture problem worth checking.